Stainless-works 200-233 Chevy/GMC Truck LS 4.8/5.3/6.0/6.2L 2009+ User Manual download pdf

Installation Instructions

Part Number 200-233

2009-12 Chevrolet Silverado 1500

Tahoe/Suburban1500/Avalanche/

GMC Sierra 1500

Yukon/Yukon XL/Denali/Denali XL

Cadillac Escalade/ESV/EXT

4.8L, 5.3L, 6.0L*, 6.2L V-8

*With Electric Cooling Fans Only*

*Does not fit 2011 6.0l motors

Packing List:

#1 720-472 Airaid Premium Filter 1

#2 KIT233MAFDAC MAF Panel 1

#3 KIT196RRDAMC Rear Air Dam Panel 1

#4 KIT996T Airaid Intake Tube 1

#5 KIT233A Air Filter Adapter 1

#6 KITHUMPHS02 Urethane Hump Hose 1

#7 KITCOUPLER10 Urethane Coupler 1

#8 KITHOSE06 3/8” x 14” Breather Hose 1

#9 KITWSTRIP02 Weather Strip 20 3/4” 1

KIT233HP Hardware & Instructions 1

#10 KIT6C31MXPPZ 6-32 x 5/16” Screw 5

#11 KIT6NWSAPZ #6 Flat Washer 5

#12 KIT6CNKEPZ 6-32 Keps Nut 5

#13 KIT15BHC3063 8-32 x 5/8” Button Head Bolt 2

#14 KIT15DHC3050 1/4 - 20 x 1/2” Button Head Bolt 3

#15 KIT09FWZ019 1/4” Flat Washer 7

#16 KIT60C250HCS M6 - 1 x 25 Hex Bolt 4

#17 KITHS64 #64 Hose Clamp 4

#18 KITFITTING01 1/4” NPT x 3/8” Barb Fitting 1

Tools Required For Installation:

5/16”, 10mm Sockets

Ratchet & Extension

Phillips Screwdriver, T15 Torx Bit

3/32”, 5/32” Allen Wrench

1. Disconnect the negative battery cable.

Remove the factory beauty cover by lifting up on

the front, and then pulling the cover towards the

front of the vehicle. It is only held in place by

grommets.

2. Disconnect the factory breather hose at the

valve cover by pulling the small black tab on the

fitting towards the front of the vehicle, and then

to the right.

3. Separate the factory intake tube from the plas-

tic clamp that secures the radiator hose to the

tube. A firm downward push will usually do it.

4. Loosen two hose clamps on the factory intake

tube. One at the throttlebody, and one where it

clamps to the factory airbox. Remove the factory

intake tube from the vehicle.

5. Remove, and set aside the MAF (Mass Air

Flow) sensor from the factory airbox. This will

require a T15 Torx Bit.

6. Rock the factory airbox back and forth to loos-

en it from the mounting grommets, and remove it

from the vehicle.

7. Using a 10mm socket, remove four bolts, and

then remove the factory airbox mounting plate

from the vehicle.

8. Assemble the Cool Air Dam panels (CAD) (#2

& #3) using five 6-32 x 5/16” screws (#10), #6

flat washers (#11), and 6-32 keps nuts (#12). Next

install the air filter adapter (#5) into the panels as

shown with the hole for the Mass Air Flow sen-

sor facing up, using three 1/4 - 20 x 1/2” button

head bolts (#14), and 1/4” flat washers (#15).

9. Install the Airaid CAD assembly into the vehi-

cle replacing the factory airbox. Secure the CAD

using four M6 x 1.25 Hex Bolt (#16), and 1/4”

flat washers (#15). Do not over tighten the four

bolts.

1 2

Packing List: 1
Before! 2

Summary of Contents

Page 1 - Packing List:

Installation Instructions Part Number 200-233 2009-12 Chevrolet Silverado 1500 Tahoe/Suburban1500/Avalanche/ GMC Sierra 1500 Yukon/Yukon XL/Denali/Den

Page 2 - Before!

14. Double check your work! Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight. 15.

Comments to this Manuals

No comments

Stainless-works 200-233 Chevy/GMC Truck LS 4.8/5.3/6.0/6.2L 2009+ User Manual

Browse online or download User Manual for For the car Stainless-works 200-233 Chevy/GMC Truck LS 4.8/5.3/6.0/6.2L 2009+ . Stainless Works 200-233 Chevy/GMC Truck LS 4.8/5.3/6.0/6.2L 2009+ AIRAID Intake System User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Stainless-works 200-233 Chevy/GMC Truck LS 4.8/5.3/6.0/6.2L 2009+